3/4" PVC-40 Conduit Fill Chart
This page shows the maximum number of conductors allowed in a 3/4-inch PVC Schedule 40 Conduit (PVC-40) conduit per the National Electrical Code. The 3/4" PVC-40 has an internal cross-sectional area of 0.508 square inches, which determines how many wires of each size can legally fit inside. Use the tables below to quickly look up conductor capacity for your installation, or use the calculator for custom configurations.
THHN/THWN-2 Maximum Conductors in 3/4" PVC-40
THHN/THWN-2 is the most commonly used conductor type in commercial and residential wiring. The table below shows the maximum number of THHN/THWN-2 conductors allowed in this 3/4" PVC-40 conduit based on NEC Chapter 9 fill rules. For 3 or more conductors the 40% fill rule applies. Values of 0 mean the conductor is too large to fit even a single wire in this conduit size.
| Wire Size | Wire Area (sq.in.) | Max Conductors | Fill at Max (sq.in.) |
|---|---|---|---|
| 14 AWG | 0.0097 | 20 | 0.1940 |
| 12 AWG | 0.0133 | 15 | 0.1995 |
| 10 AWG | 0.0211 | 9 | 0.1899 |
| 8 AWG | 0.0366 | 5 | 0.1830 |
| 6 AWG | 0.0507 | 4 | 0.2028 |
| 4 AWG | 0.0824 | 1 | 0.0824 |
| 3 AWG | 0.0973 | 1 | 0.0973 |
| 2 AWG | 0.1158 | 1 | 0.1158 |
| 1 AWG | 0.1562 | 1 | 0.1562 |
| 1/0 AWG | 0.1855 | 1 | 0.1855 |
| 2/0 AWG | 0.2223 | 1 | 0.2223 |
| 3/0 AWG | 0.2679 | 1 | 0.2679 |
| 4/0 AWG | 0.3237 | 0 | N/A |
| 250 AWG | 0.3970 | 0 | N/A |
| 300 AWG | 0.4608 | 0 | N/A |
| 350 AWG | 0.5242 | 0 | N/A |
| 400 AWG | 0.5863 | 0 | N/A |
| 500 AWG | 0.7073 | 0 | N/A |
About 3/4" PVC Schedule 40 Conduit
PVC Schedule 40 is the standard non-metallic conduit for underground installations, concrete encasement, and wet locations. It resists corrosion, chemicals, and moisture, making it ideal for direct burial applications, underground service entrances, and outdoor runs where the conduit is not exposed to physical damage. It is widely used for residential underground feeder circuits and commercial site wiring. The 3/4-inch trade size is one of the standard sizes defined in NEC Chapter 9, Table 4. With an internal area of 0.508 square inches, it provides adequate space for a range of conductor sizes and counts depending on the application requirements.
PVC Schedule 40 is made from polyvinyl chloride with a moderate wall thickness. It uses solvent-cemented joints that create watertight connections. The internal area is slightly smaller than EMT of the same trade size due to the wall thickness required for structural integrity.
NEC Reference: NEC Article 352 governs the installation requirements for PVC-40 conduit. Conduit fill is calculated using NEC Chapter 9, Table 1 (fill percentages), Table 4 (conduit areas), and Table 5 (conductor areas). This calculator uses the exact values from these tables for accurate results.
Worked Example: 12 AWG THHN in 3/4" PVC-40
Here is a step-by-step example showing how to calculate conduit fill for 4 conductors of 12 AWG THHN/THWN-2 in this 3/4" PVC-40 conduit. This is a common scenario for a 20-amp branch circuit requiring two hots, a neutral, and a ground.
- Identify the conduit internal area: 3/4" PVC-40 = 0.508 sq.in. (from NEC Table 4)
- Identify the conductor area: 12 AWG THHN/THWN-2 = 0.0133 sq.in. per conductor (from NEC Table 5)
- Calculate total conductor area: 4 conductors x 0.0133 sq.in. = 0.0532 sq.in.
- Determine the fill percentage rule: 4 conductors uses the 40% fill rule (NEC Table 1)
- Calculate allowable fill area: 0.508 sq.in. x 0.40 = 0.2032 sq.in.
- Compare: Total conductor area (0.0532 sq.in.) is less than allowable fill (0.2032 sq.in.) — COMPLIANT
- Actual fill percentage: 0.0532 / 0.508 = 10.5%
- Maximum conductors: This 3/4" PVC-40 can hold up to 15 conductors of 12 AWG THHN/THWN-2 per NEC rules
XHHW Maximum Conductors in 3/4" PVC-40
XHHW conductors use cross-linked polyethylene insulation, which provides excellent moisture and heat resistance. XHHW has slightly different insulation dimensions than THHN, resulting in different fill counts. The table below shows the maximum XHHW conductors allowed in this 3/4" PVC-40 conduit.
| Wire Size | Wire Area (sq.in.) | Max Conductors |
|---|---|---|
| 14 AWG | 0.0139 | 14 |
| 12 AWG | 0.0181 | 11 |
| 10 AWG | 0.0243 | 8 |
| 8 AWG | 0.0437 | 4 |
| 6 AWG | 0.0590 | 3 |
| 4 AWG | 0.0814 | 1 |
| 3 AWG | 0.0962 | 1 |
| 2 AWG | 0.1146 | 1 |
| 1 AWG | 0.1534 | 1 |
| 1/0 AWG | 0.1825 | 1 |
| 2/0 AWG | 0.2190 | 1 |
| 3/0 AWG | 0.2642 | 1 |
| 4/0 AWG | 0.3197 | 0 |
| 250 AWG | 0.3904 | 0 |
| 300 AWG | 0.4536 | 0 |
| 350 AWG | 0.5166 | 0 |
| 400 AWG | 0.5782 | 0 |
| 500 AWG | 0.6984 | 0 |
Installation Advantages of PVC-40
Corrosion-proof and chemical-resistant. Lowest cost for underground installations. Lightweight and easy to assemble with solvent cement. Watertight joints without special fittings. Does not require painting or galvanizing.
Installation Requirements
PVC connections are made with solvent cement (glue), creating permanent, watertight joints. Expansion fittings are required where temperature changes may cause expansion or contraction. A separate equipment grounding conductor is always required since PVC is non-conductive. PVC must not be used in locations where ambient temperature exceeds 50 degrees C (122 degrees F).
When planning your installation with 3/4" PVC-40 conduit, remember that the fill calculation only addresses the straight sections. The number of bends, total conduit length, and pulling tension also affect whether the installation is practical. The NEC limits total bends to 360 degrees (four 90-degree bends) between pull points. For long runs or runs with many bends, consider using the next larger conduit size even if the fill calculation passes, as this will reduce pulling tension and make future maintenance easier.
Other PVC-40 Sizes
Browse fill charts for other PVC Schedule 40 Conduit trade sizes. Larger conduit sizes accommodate more conductors and are needed for high-ampacity circuits or runs with many wires.